Senior Testing Engineer - Military Engines

• Coordinate, prepare and perform diesel engine development, calibration and engineering support work in an engine dynamometer test cell, on HiL/MiL systems and if necessary, in the field.
• Focus is on diesel engines for military applications. Depending on the business situation, the same scope of work on commercial heavy-duty diesel engines is expected.
• Develop, analyze and evaluate unique engineering solutions with consideration of factors such as system effectiveness, reliability, configuration, emission regulations, customer requirements and cost.
• Coordinate, support and perform commissioning and testing of prototype engines/vehicles and early production units together with the customer and their sub-contractors with regards to our scope for applications including but not limited to wheeled/tracked military vehicles, mining equipment, marine, rail, and oil and gas.
• Develop technically reasonable and feasible alternatives with regards to time and money for challenges occurring during the progress of the project.
• Support customers in case of irregularities. Support and troubleshoot field failures.
• Facilitate communication between customer and different engineering groups.
• Ability to read and understand controller wiring diagrams and integration including ability to make custom harnesses for vehicle and test benches. Experience at CAN-Bus troubleshooting and monitoring.
• Provide field support for After Sales and Applications departments whenever complex issues require engineering support.
• Communicate and consult with Engineering and Design departments worldwide.
• Provide support for production and train production staff whenever complex issues require engineering support.
• Maintains daily record of work hours by job number for budgeting & auditing purposes
• Document the preparation, execution and analysis of tasks performed according to highest engineering standards.
• Manage, track and communicate project status and assist in managing project budget and project forecast.
• Mentor and train less experienced engineers
• Maintain a clean and safe work environment.
• Promote a compliance culture and live the latter and the spirit of the Rolls-Royce Code of Conduct.
• Perform special projects as required.

Required

-

Bachelor's degree in Mechanical Engineering, Electrical Engineering or Automotive Engineering and 3 years of engineering experience testing and calibrating combustion engines in a dynamometer test cell and in the field; or 7 years of engineering experience testing and calibrating combustion engines in a dynamometer test cell and in the field.

-

Excellent knowledge of the principles and complete operation of internal combustion engines and diesel engine technology

-

Excellent experience diagnosing diesel engines in test cells and installed in a vehicle

-

Excellent experience with troubleshooting mechanical, electrical and hydraulic components of diesel engines

-

Excellent knowledge of engine control units and their operation

-

Experience with engine-specific instrumentation, data acquisition systems, signal processing and data management

-

Strong skills in the use of measurement and testing tools for mechanical and electrical systems

-

Strong knowledge in the physical properties of fuels, coolants, lubricants and oils

-

Excellent project management skills.

-

Excellent organizational, planning and follow-up skills

-

Very strong interpersonal skills

-

Excellent work and time management skills

-

Excellent oral and written communication skills

-

Ability to bend down, stand over, lay down and complete work tasks within the tight confines typical of marine engine compartments and/or engine rooms for long periods of time

-

Ability to lift, push, pull weights in the 20-60 lb range

-

Must be available to work flexible hours including night shifts and weekends

-

U.S. Citizenship required as this position occasionally will be working under a government contract

-

Ability to travel 50-80% on short notice domestic and international

-

Strong ability to adapt to new circumstances quickly

Preferred

• -
• Master's degree in Mechanical, Electrical engineering or related field
• -

Knowledge of MTU, Daimler, and Detroit Diesel Controllers

-

Experience with ETAS INCA, MTU Diasys and Xentry

• -
• Knowledge of test cell automation systems
• -
• Experience working with authorities/military customers
• -
• MTU product knowledge
• -
• Experience in operating fork lift trucks
• -
• Experience in rigging of weights up to 1 ton
• -
• Strong knowledge, experience and skills in installing and repairing diesel engines – especially in confined spaces
• -
• Proven ability to operate machine shop equipment used for fabricating test parts and equipment
• -
• Strong skills in the use of mechanical and electrical hand tools
• All your information will be kept confidential according to EEO guidelines.